AWS Certified Advanced Networking - Specialty ANS-C01 Practice Test

AWS Certified Advanced Networking - Specialty ANS-C01 Practice Test practice questions, page 8 of 13, with answer review and explanations.

Question 36

A network engineer needs to update a company's hybrid network to support IPv6 for the upcoming release of a new application. The application is hosted in a VPC in the AWS Cloud. The company's current AWS infrastructure includes VPCs that are connected by a transit gateway. The transit gateway is connected to the on-premises network by AWS Direct Connect and AWS Site-to-Site VPN. The company's on-premises devices have been updated to support the new IPv6 requirements. The company has enabled IPv6 for the existing VPC by assigning a new IPv6 CIDR block to the VPC and by assigning IPv6 to the subnets for dual-stack support. The company has launched new Amazon EC2 instances for the new application in the updated subnets. When updating the hybrid network to support IPv6 the network engineer must avoid making any changes to the current infrastructure. The network engineer also must block direct access to the instances' new IPv6 addresses from the internet. However, the network engineer must allow outbound internet access from the instances. What is the MOST operationally efficient solution that meets these requirements?

  1. Update the Direct Connect transit VIF and configure BGP peering with the AWS assigned IPv6 peering address. Create a new VPN connection that supports IPv6 connectivity. Add an egress-only internet gateway. Update any affected VPC security groups and route tables to provide connectivity within the VPC and between the VPC and the on-premises devices
  2. Update the Direct Connect transit VIF and configure BGP peering with the AWS assigned IPv6 peering address. Update the existing VPN connection to support IPv6 connectivity. Add an egress-only internet gateway. Update any affected VPC security groups and route tables to provide connectivity within the VPC and between the VPC and the on-premises devices.
  3. Create a Direct Connect transit VIF and configure BGP peering with the AWS assigned IPv6 peering address. Create a new VPN connection that supports IPv6 connectivity. Add an egress-only internet gateway. Update any affected VPC security groups and route tables to provide connectivity within the VPC and between the VPC and the on-premises devices.
  4. Create a Direct Connect transit VIF and configure BGP peering with the AWS assigned IPv6 peering address. Create a new VPN connection that supports IPv6 connectivity. Add a NAT gateway. Update any affected VPC security groups and route tables to provide connectivity within the VPC and between the VPC and the on-premises devices.

Question 37

A network engineer must provide additional safeguards to protect encrypted data at Application Load Balancers (ALBs) through the use of a unique random session key. What should the network engineer do to meet this requirement?

  1. Change the ALB security policy to a policy that supports TLS 1.2 protocol only
  2. Use AWS Key Management Service (AWS KMS) to encrypt session keys
  3. Associate an AWS WAF web ACL with the ALBs. and create a security rule to enforce forward secrecy (FS)
  4. Change the ALB security policy to a policy that supports forward secrecy (FS)

Question 38

A company has deployed a software-defined WAN (SD-WAN) solution to interconnect all of its offices. The company is migrating workloads to AWS and needs to extend its SD-WAN solution to support connectivity to these workloads. A network engineer plans to deploy AWS Transit Gateway Connect and two SD-WAN virtual appliances to provide this connectivity. According to company policies, only a single SD-WAN virtual appliance can handle traffic from AWS workloads at a given time. How should the network engineer configure routing to meet these requirements?

  1. Add a static default route in the transit gateway route table to point to the secondary SD-WAN virtual appliance. Add routes that are more specific to point to the primary SD-WAN virtual appliance.
  2. Configure the BGP community tag 7224:7300 on the primary SD-WAN virtual appliance for BGP routes toward the transit gateway.
  3. Configure the AS_PATH prepend attribute on the secondary SD-WAN virtual appliance for BGP routes toward the transit gateway.
  4. Disable equal-cost multi-path (ECMP) routing on the transit gateway for Transit Gateway Connect.

Question 39

A company is planning to deploy many software-defined WAN (SD-WAN) sites. The company is using AWS Transit Gateway and has deployed a transit gateway in the required AWS Region. A network engineer needs to deploy the SD-WAN hub virtual appliance into a VPC that is connected to the transit gateway. The solution must support at least 5 Gbps of throughput from the SD-WAN hub virtual appliance to other VPCs that are attached to the transit gateway. Which solution will meet these requirements?

  1. Create a new VPC for the SD-WAN hub virtual appliance. Create two IPsec VPN connections between the SD-WAN hub virtual appliance and the transit gateway. Configure BGP over the IPsec VPN connections
  2. Assign a new CIDR block to the transit gateway. Create a new VPC for the SD-WAN hub virtual appliance. Attach the new VPC to the transit gateway with a VPC attachment. Add a transit gateway Connect attachment. Create a Connect peer and specify the GRE and BGP parameters. Create a route in the appropriate VPC for the SD-WAN hub virtual appliance to route to the transit gateway.
  3. Create a new VPC for the SD-WAN hub virtual appliance. Attach the new VPC to the transit gateway with a VPC attachment. Create two IPsec VPN connections between the SD-WAN hub virtual appliance and the transit gateway. Configure BGP over the IPsec VPN connections.
  4. Assign a new CIDR block to the transit gateway. Create a new VPC for the SD-WAN hub virtual appliance. Attach the new VPC to the transit gateway with a VPC attachment. Add a transit gateway Connect attachment. Create a Connect peer and specify the VXLAN and BGP parameters. Create a route in the appropriate VPC for the SD-WAN hub virtual appliance to route to the transit gateway.

Question 40

A company is deploying a new application on AWS. The application uses dynamic multicasting. The company has five VPCs that are all attached to a transit gateway Amazon EC2 instances in each VPC need to be able to register dynamically to receive a multicast transmission. How should a network engineer configure the AWS resources to meet these requirements?

  1. Create a static source multicast domain within the transit gateway. Associate the VPCs and applicable subnets with the multicast domain. Register the multicast senders' network interface with the multicast domain. Adjust the network ACLs to allow UDP traffic from the source to all receivers and to allow UDP traffic that is sent to the multicast group address.
  2. Create a static source multicast domain within the transit gateway. Associate the VPCs and applicable subnets with the multicast domain. Register the multicast senders' network interface with the multicast domain. Adjust the network ACLs to allow TCP traffic from the source to all receivers and to allow TCP traffic that is sent to the multicast group address.
  3. Create an Internet Group Management Protocol (IGMP) multicast domain within the transit gateway. Associate the VPCs and applicable subnets with the multicast domain. Register the multicast senders' network interface with the multicast domain. Adjust the network ACLs to allow UDP traffic from the source to all receivers and to allow UDP traffic that is sent to the multicast group address.
  4. Create an Internet Group Management Protocol (IGMP) multicast domain within the transit gateway. Associate the VPCs and applicable subnets with the multicast domain. Register the multicast senders' network interface with the multicast domain. Adjust the network ACLs to allow TCP traffic from the source to all receivers and to allow TCP traffic that is sent to the multicast group address.